HTI DALI 105/230…240 DIM

Product family benefits
  • Very low power consumption thanks to high efficiency
  • Through-wiring possible on the primary side
  • Large temperature range
  • Protective operation throughout the entire partial-load range for long lamp life
Areas of application
  • Effect and accent lighting
  • Living rooms
  • Object lighting
  • Conference rooms
  • Restaurants
  • Recessed and surface-mounted ceiling luminaires
  • Shop lighting
  • Event rooms

Technical Data

Electrical data

Lamp wattage

35…105 W

Maximum output power

105 W

Line current

0.45 A

Input voltage DC

176…275 V

Nominal voltage

230…240 V

Power factor λ

0.95

Minimum

Operating frequency

40 kHz

Approximately

Nominal output voltage

11.6 / 11.4 V

Mains frequency

50…60 Hz

System wattage

108.00 W

Efficiency in full-load

95 %

Max. ECG no. on circuit breaker 10 A (B)

23

Galvanic isolation primary/secondary

4.00 kV

Max. ECG no. on circuit breaker 16 A (B)

38

Networked standby power

0.50 W

Inrush current

0.6 A

Dimensions & weight

Length

170.0 mm

Width

44.0 mm

Height

34.0 mm

Wire preparation length, input side

8.0 mm

Wire preparation length, output side

8.0 mm

Mounting hole spacing, length

140.0 mm

Product weight

160.00 g

Temperatures & operating conditions

Ambient temperature range

-20…+50 °C

Maximum temperature at tc test point

75 °C

Additional product data

Design / version

Long with cable clamp

Capabilities

Dimming method

Phase cut-off

Dimming interface

DALI or Touch DIM/Touch DIM Sensor

Overload protection

Automatic reversible

Overheating protection

Automatic reversible

Short-circuit protection

Automatic reversible

Max. cable length to lamp/LED module

2.0 m

Cable/wire types, input side

H03VV-F 2x0.50 / H03VV-F 2x0.75 / H03VVH2-F 2x0.75 / H05VVH2-F 2x0.75 / H05VV-F 2x2.5 / H05VV5G 1.5 / NYM-O 2x1.5 / NYM-J 3x1.5 / NYM-J 5x1.5 mm²

Cable/wire types, output side

H03VV-F 2x0.75 / H05VV-F 2x0.75 / H05VV-F 2x1.5 / H05VV-F 2x2.5 / NYM-J 3x1.5 / NYM-J 3x2.5 / NYM-O 2x1.5 mm²

Dimmable

Yes

Dimming range

0.1…100 %

With AC; 1…100% with DC

No-load proof

Yes

Intended for no-load operation

No

Certificates & standards

Approval marks – approval

E1 approval / VDE / VDE-EMC

Standards

Acc. to EN 55015:2006 + A1:2007/Acc. to EN 61000-3-2/Acc. to EN 61547/Acc. to EN 61347-2-2

Type of protection

IP20

Logistical data

Commodity code

85044095900

Environmental information


Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)

Date of Declaration

21-04-2023

Primary Article Identifier

4008321420633

Candidate List Substance 1

Lead

CAS No. of substance 1

7439-92-1

Safe Use Instruction

The identification of the Candidate List substance is sufficient to allow safe use of the article.

Declaration No. in SCIP database

9345a0a7-e3a5-49b7-880f-5f065a3e772f

Packaging information

EAN

Unit

Piece

Dimension l x w x h

Weight

Volume

4008321420633 UNV

Unpacked

1 189.00g
4008321420640 VS

Shipping box

10 235mm x 183mm x 89mm 1889.00g 3.83dm³

Downloads

Information about Family

The HALOTRONIC HTi is a DALI transformer for use with low voltage halogen lamps, and is suitable where you need dimming below 1 %. Highly energy-efficient, it provides short-circuit, overtemperature and overload protection (electronically reversible) and electrical isolation between the primary and secondary sides. It does not allow switching between the electronic transformer and the lamp. HALOTRONIC HTi is suitable for use inside; for effect and accent lighting, object lighting, recessed and surface-mounted ceiling light fittings and for the illumination of spaces such as conference rooms and living rooms. It is also good for shoplighting and restaurant lighting. It consumes little power, yet has a large temperature range, and its protective operation throughout the entire partial-load range promotes lamp life. You can through-wire HALOTRONIC HTi on the primary side.
Product family features
  • DALI transformer for low voltage halogen lamps
  • Electrical isolation between the primary side and the secondary side
  • Short-circuit protection, overload protection, overtemperature protection: electronically reversible
  • Device fits also for special applications where dimming below 1 % is required
Ecodesign regulation information:
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.

Products

Sort by:
Product
Dimmable
Height
Width
Nominal voltage
Lamp wattage
Data sheet
HTI DALI 105/230…240 DIM
Yes 34.0 mm 44.0 mm 230…240 V 35…105 W