IT FIT 60/220...240/1A4 CS
Product family benefits
- Higher quality of light thanks to low output ripple current
- High flexibility due to four different output currents
- Small housing for flexible luminaire designs
- High efficiency
Areas of application
- Suitable for downlights, spotlights and LED panels
- Suitable for luminaires of protection classes I and II
Technical Data
Electrical data
Nominal input voltage
220…240 V
Mains frequency
50…60 Hz
Input voltage AC
198…264 V
Total harmonic distortion
< 10 %
Power factor λ
0.98
Efficiency in full-load
90 %
Device power loss
6.5 W
Protective conductor current
<0.7 mA
Inrush current
< 50 A
Max. ECG no. on circuit breaker 10 A (B)
25
Max. ECG no. on circuit breaker 10 A (C)
37
Max. ECG no. on circuit breaker 16 A (C)
60
Max. ECG no. on circuit breaker 16 A (B)
40
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
27…57 / 27…52 / 27…48 / 27…43 / 27…40 V
U-OUT (working voltage)
70 V
Nominal output current
825 / 900 / 975 / 1050 / 1000 / 1200 / 1300 / 1400 mA
Output current tolerance
±5 %
Output ripple current (100 Hz)
< 3 %
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
22.3…60 W
Maximum output power
60 W
Galvanic isolation
SELV
Default output current
1400 mA
Galvanic isolation primary/secondary
SELV
Current set
DipSwitch
Dimensions & weight
Mounting hole spacing, length
94.0 mm
Mounting hole spacing, width
58.0 mm
Product weight
155.00 g
Cable cross-section, input side
0.5…1.5 / 0.75…1.5 mm²
Cable cross-section, output side
0.5…1.5 / 0.75…1.5 mm²
Wire preparation length, input side
7…8 mm
Wire preparation length, output side
7…8 mm
Height
29.5 mm
Length
103.0 mm
Width
67.0 mm
Colors & materials
Casing material
Plastic
Temperatures & operating conditions
Ambient temperature range
-20…+50 °C
Maximum temperature at tc test point
70 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-40…+85 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
50000 h
Additional product data
Encapsulated
No
Capabilities
Dimmable
No
Overheating protection
Automatic switch off, reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I / II
Type of connection, input side
Push terminal
Type of connection, output side
Push terminal
Suitable for through-wiring
Yes with optional cable clamp
Programming interface
Dipswitch
Number of channels
1
Programming
Programming device
DIPswitch
Certificates & standards
Approval marks – approval
ENEC 05 / CCC / RCM / CE
Standards
Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
Type of protection
IP20
Protection class
II
Logistical data
Commodity code
85044083900
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
16-10-2023
Primary Article Identifier
4062172306072
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
c794346c-4129-4db6-8e47-8f306063f90d
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4062172306072 |
UNV
| 1 | 103mm x 67mm x 30mm | 155.00g | 0.20dm³ |
| 4062172306089 |
VS
| 20 | 353mm x 223mm x 95mm | 3410.00g | 7.48dm³ |
Downloads
Data sheets
Accessories optional
Information about Family
Product family features
- Lifetime: up to 50,000 h (temperature at max. tc )
- Cable clamp kit for independent mounting
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
|
IT FIT 60/220...240/1A4 CS
|
27…57 / 27…52 / 27…48 / 27…43 / 27…40 V | 825 / 900 / 975 / 1050 / 1000 / 1200 / 1300 / 1400 mA | 103.0 mm | 67.0 mm | 29.5 mm | ||
|
OT FIT 75/220-240/1A6 CS
|
27…57 / 27…42 V | 1200 / 1350 / 1500 / 1650 mA | 103.0 mm | 67.0 mm | 29.5 mm |