OT FIT 40/220…240/1A0 CS
Product family benefits
- Higher quality of light thanks to low output ripple current
- High flexibility due to four different output currents
- Small housing for flexible luminaire designs
- High efficiency
Areas of application
- Suitable for downlights, spotlights and LED panels
- Suitable for luminaires of protection classes I and II
Technical Data
Electrical data
Nominal input voltage
220…240 V
Mains frequency
50/60 Hz
Input voltage AC
198…264 V
Total harmonic distortion
< 10 %
Power factor λ
0.98
Efficiency in full-load
90 %
Device power loss
4.9 W
Protective conductor current
<0.7 mA
Inrush current
≤ 35 A
Max. ECG no. on circuit breaker 10 A (C)
19
Max. ECG no. on circuit breaker 10 A (B)
11
Max. ECG no. on circuit breaker 16 A (C)
31
Max. ECG no. on circuit breaker 16 A (B)
19
Max. ECG no. on circuit breaker 25 A (B)
29
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
25…42 / 30…42 V
U-OUT (working voltage)
60 V
Nominal output current
800 / 900 / 950 / 1050 mA
Output current tolerance
±7.5 %
Default output current
1050 mA
Output ripple current (100 Hz)
< 5 %
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
20…44.1 W
Maximum output power
44.1 W
Galvanic isolation
SELV
Current set
DipSwitch
Galvanic isolation primary/secondary
SELV
Dimensions & weight
Mounting hole spacing, length
88.0 mm
Mounting hole spacing, width
34.0 mm
Product weight
110.00 g
Cable cross-section, input side
0.5…1.5 mm²
Cable cross-section, output side
0.5…1.5 mm²
Wire preparation length, input side
7…8 mm
Wire preparation length, output side
7…8 mm
Length
97.0 mm
Width
43.0 mm
Height
29.5 mm
Colors & materials
Casing material
Plastic
Temperatures & operating conditions
Ambient temperature range
-20…+50 °C
Maximum temperature at tc test point
80 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-20…80 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
50000 h
Additional product data
Predecessor EAN
4052899435650
Capabilities
Dimmable
No
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I / II
Type of connection, input side
Push terminal
Type of connection, output side
Push terminal
Detection angle (Light sensor)
-
Suitable for through-wiring
No
Control interface
-
Detection angle (PIR)
-
Number of channels
1
Programming
Programming device
DIPswitch
Certificates & standards
Approval marks – approval
CCC / CE / RCM / ENEC 05
Standards
Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
Type of protection
IP20
Protection class
I,II
Logistical data
Commodity code
850440839000
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
26-05-2023
Primary Article Identifier
4052899617339
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
06ee480d-1593-42d1-9ca2-8009fd63d4df
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4052899617339 |
UNV
| 1 | |||
| 4052899617797 |
VS
| 20 | 228mm x 208mm x 78mm | 2403.00g | 3.70dm³ |
Downloads
Data sheets
Accessories optional
Information about Family
Product family features
- Lifetime: up to 50,000 h (temperature at max. tc )
- Cable clamp kit for independent mounting
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
OT FIT 20/220…240/500 CS
|
23…42 V | 250 / 350 / 450 / 500 mA | 97.0 mm | 43.0 mm | 29.5 mm | ||
|
OT FIT 30/220…240/700 CS
|
23…42 V | 500 / 600 / 650 / 700 mA | 97.0 mm | 43.0 mm | 29.5 mm | ||
|
|
OT FIT 40/220…240/1A0 CS
|
25…42 / 30…42 V | 800 / 900 / 950 / 1050 mA | 97.0 mm | 43.0 mm | 29.5 mm |