OT FIT 40/220 240/1A0 LT2 LP
- Versatile scope of application due to output power range of up to 40 W
- Fulfill safety requirement due to overload, overtemperature protection
- High efficiency
- Higher quality of light thanks to < 5% output ripple current
- Installation in emergency lighting systems according to IEC 61347-2-13, appendix J
- Luminaires with flexible current setting (LEDset2)
- Suitable for indoor SELV installations
- Suitable for luminaires of protection classes I and II
- Suitable for downlights, spotlights and LED panels
- Independent mounting via Cable Clamp Kit possible
Technical Data
Electrical data
Nominal input voltage
220 240 V
Mains frequency
0/50/60 Hz
Input voltage AC
198 264 V
Input voltage DC
176 276 V
Total harmonic distortion
< 15 %
Power factor λ
0.98
Efficiency in full-load
87 %
Device power loss
6.0 W
Inrush current
17 A
Max. ECG no. on circuit breaker 10 A (B)
19
Max. ECG no. on circuit breaker 16 A (B)
30
Max. ECG no. on circuit breaker 25 A (B)
-
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
15 50 V
U-OUT (working voltage)
60 V
Nominal output current
500 1050 mA
Output current LEDset open
Not allowed
Output current LEDset shorted
1050 mA
Output current tolerance
±5 %
Output ripple current (100 Hz)
< 5 %
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
13 40 W
Maximum output power
40 W
Galvanic isolation
SELV
Current set
LEDset2
Galvanic isolation primary/secondary
SELV
Dimensions & weight
Mounting hole spacing, length
94.0 mm
Mounting hole spacing, width
58.0 mm
Product weight
135.00 g
Cable cross-section, input side
0.5 1.5 mm²
Cable cross-section, output side
0.5 1.5 mm²
Wire preparation length, input side
9.0 10.0 mm
Wire preparation length, output side
8.0 9.0 mm
Length
103.0 mm
Width
67.0 mm
Height
22.5 mm
Colors & materials
Casing material
Plastic
Temperatures & operating conditions
Ambient temperature range
-20 +45 °C
Maximum temperature at tc test point
75 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-40 +85 °C
Permitted rel. humidity during operation
5 85 %
Lifespan
ECG lifetime
50000 / 100000 h
Additional product data
Predecessor EAN
4052899166318
Capabilities
Dimmable
No
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I / II
Type of connection, output side
Push terminal
Number of channels
1
Suitable for emergency lighting
Yes
Suitable for through-wiring
Yes
Programming
Programming device
LEDset
Certificates & standards
Approval marks approval
CE / UKCA / ENEC / CCC / EL / RCM / BIS / EAC
Standards
Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to IEC 61000-3-2/Acc. to IEC 61547/Acc. to EN 55015
Type of protection
IP20
Protection class
II
Logistical data
Commodity code
850440839000
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
26-05-2023
Primary Article Identifier
4052899490734
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
5c5c1e01-8518-4cb8-bd43-a31141b276b3
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
---|---|---|---|---|---|
4052899490734 |
UNV
| 1 | 103mm x 67mm x 23mm | 135.00g | 0.16dm³ |
4052899490741 |
VS
| 20 | 348mm x 218mm x 67mm | 2862.00g | 5.08dm³ |
Downloads
Data sheets
Accessories optional
Information about Family
This extra flat LED driver offers flexibility at choosing compatible LED modules due to the very wide operating window. Some other highlights include the capability for DC-input, the suitability for emergency installations and the optional cable clamp that allows independent installations and trough-looping.
- Supply voltage: 220 240 V
- Line frequency: 0 Hz | 50 Hz | 60 Hz
- Line voltage: 198 264 V
- According to EN 61347-1, 61347-2-13, 62384
- RI suppression: to EN 55015
- Line harmonics according to EN 61000-3-2
- Immunity according to EN 61547
- Lifetime: up to 100,000 h (temperature at Tc = 65 °C, max. 10 % failure rate)
- Independent connection via through-looping (depending on version of product)
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
Product |
|
|
|
|
|
Data sheet | ||
---|---|---|---|---|---|---|---|---|
![]() |
OT FIT 15/220
240/500 LT2 LP
|
15 50 V | 150 500 mA | 103.0 mm | 67.0 mm | 22.5 mm | ||
![]() |
OT FIT 25/220
240/700 LT2 LP
|
15 50 V | 300 700 mA | 103.0 mm | 67.0 mm | 22.5 mm | ||
![]() |
OT FIT 40/220
240/1A0 LT2 LP
|
15 50 V | 500 1050 mA | 103.0 mm | 67.0 mm | 22.5 mm |