OTi DALI 80/220…240/1A6 LT2 L
Product family benefits
- Fully programmable via software (DALI Interface)
- Flexible current setting (LEDset2)
- Lifetime: up to 100,000 h (temperature at Tc = 65 °C, max. 10 % failure rate)
- High-quality dimming of 1…100 % by amplitude dimming (except 80 W versions)
- High quality of light thanks to <1% output ripple current
- Very high efficiency
- Very low standby power consumption: < 0.15 W *
- Fulfill safety requirement due to overload, overtemperature, Hot Plug protection
- Easy to use in corridors and restrooms because of three-level Corridor function
- Touch DIM application: easy to control via pushbutton or sensor
- Energy efficient Touch DIM operation due to automatic switch-off at sufficient residual light
- Suitable for emergency Installations (acc. to EN 60598-2-22 and IEC 61347-2-13, appendix J) thanks to DC detection (0 Hz, pulsating DC), on/off switchable
- Feedback of power consumption and operating hours (Fit for SMART GRID)
- Suitable for buildings according to EPBD/BREEAM/LEED due to automatic Constant Lumen Output setting
- Luminaire information for easy maintenance
Areas of application
- Linear lighting for office, education, storage areas and retail
- Installation in emergency lighting systems according to IEC 61347-2-13, appendix J
- Suitable for luminaires of protection class I
Technical Data
Electrical data
Nominal input voltage
220…240 V
Mains frequency
0/50/60 Hz
Input voltage AC
198…264 V
Input voltage DC
176…276 V
Current set
DALI / LEDset / Programmable
Total harmonic distortion
< 20 %
Power factor λ
0.78C...0.98
Efficiency in full-load
90 %
Device power loss
8.5 W
Protective conductor current
<2.0 mA
Inrush current
53 A
Max. ECG no. on circuit breaker 10 A (B)
8
Max. ECG no. on circuit breaker 16 A (B)
13
Max. ECG no. on circuit breaker 25 A (B)
-
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
20…54 V
U-OUT (working voltage)
< 60 V
Nominal output current
600…1550 mA
Output current LEDset open
300 mA
Output current LEDset shorted
1400 mA
Default output current
300 mA
Output current tolerance
±3 %
Output ripple current (100 Hz)
< 1 %
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
32…80 W
Maximum output power
80 W
Galvanic isolation
SELV
Power loss in stand-by mode
<0.5 W
Galvanic isolation primary/secondary
3.75 kV
Dimensions & weight
Mounting hole spacing, length
350.0 mm
Product weight
285.00 g
Cable cross-section, input side
0.5…1.5 mm²
Cable cross-section, output side
0.5…1.5 mm²
Wire preparation length, input side
8.5…9.5 mm
Wire preparation length, output side
8.5…9.5 mm
Width
30.0 mm
Length
360.0 mm
Height
21.0 mm
Colors & materials
Casing material
Metal
Temperatures & operating conditions
Ambient temperature range
-25…+50 °C
Maximum temperature at tc test point
80 °C
Max.housing temperature in case of fault
120 °C
Temperature range at storage
-25…85 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
50000 / 100000 h
Capabilities
Programming interface
DALI, LEDset
Dimmable
Yes
Dimming interface
DALI-2 / Touch DIM / Touch DIM Sensor
Dimming range
1…100 %
Dimming method
Amplitude Modulation / Pulse Width Modulation
Constant lumen function
Programmable
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I
Type of connection, input side
Push terminal
Type of connection, output side
Push terminal
Number of channels
1
Control interface
DALI
DALI-2 Diagnostic Data
Yes
DALI-2 Energy Data
Yes
Programming
Programming device
DALI magic
Tuner4TRONIC Field App
Yes
Programmable features
Operating Current
Yes
Lamp Operating Time
Yes
DALI Settings
Yes
Emergency Mode
Yes
DALI-2 Luminaire Data
Yes
Configuration Lock
Yes
TouchDIM + Sensor
Yes
Certificates & standards
Approval marks – approval
CE / EL / VDE-ENEC / VDE-EMC / EAC / CCC / RCM
Standards
Acc. to EN 61347-1/Acc. to EN 61347-2-13/Acc. to EN 55015/Acc. to EN 61547/Acc. to EN 61000-3-2/Acc. to EN 62384
Type of protection
IP20
Logistical data
Commodity code
850440839000
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
28-04-2023
Primary Article Identifier
4052899028074
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
cbb3b8e1-e2f1-4b9c-94d0-cb312e04ec0b
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4052899028074 |
UNV
| 1 | 360mm x 30mm x 21mm | 285.00g | 0.23dm³ |
| 4052899028081 |
VS
| 20 | 385mm x 160mm x 100mm | 5875.00g | 6.16dm³ |
Downloads
Data sheets
Information about Family
Peace of mind - intelligent, future proof, wide range of usage
A wide operating window of up to 2.1A and an efficiency of up to 91% mark some highlights of this linear LED driver. It is fully digitally programmable by DALI and LT2 and offers 0.1…100% DALI dimming. This device is also suitable for emergency lighting units.
A wide operating window of up to 2.1A and an efficiency of up to 91% mark some highlights of this linear LED driver. It is fully digitally programmable by DALI and LT2 and offers 0.1…100% DALI dimming. This device is also suitable for emergency lighting units.
Product family features
- Line frequency: 0 Hz | 50 Hz | 60 Hz
- Versatile DALI window driver up to 80 W due to flexible output characteristic
- Supply voltage: 220…240 V
- Available with output current range: up to 2,100 mA
- Constant Lumen Output (CLO)
- Integrated customizable thermal management (Driver Guard)
- DALI-2 certified (Part -101,-102 and -207)
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
OTi DALI 35/220…240/700 LT2 L G2
|
15…54 V | 200…700 mA | 360.0 mm | 30.0 mm | 21.0 mm | ||
|
OTi DALI 50/220…240/1A4 LT2 L G2
|
15…54 V | 600…1400 mA | 360.0 mm | 30.0 mm | 21.0 mm | ||
|
|
OTi DALI 80/220…240/1A6 LT2 L
|
20…54 V | 600…1550 mA | 360.0 mm | 30.0 mm | 21.0 mm | ||
|
OTi DALI 80/220…240/2A1 LT2 L
|
20…54 V | 1000…2100 mA | 360.0 mm | 30.0 mm | 21.0 mm |