OTi DALI 35/220…240/400 D LT2 UF L
Product family benefits
- Ultra-flat housing (11 mm height) for innovative luminaire designs and applications
- LEDset interface for direct Ultraflat sensor connection (LS/PD LT2 LI UF sensor)
- Fully programmable via T4T software (NFC, DALI Interface)
- Lifetime: up to 100,000 h (temperature at Tc = 65 °C, max. 10 % failure rate)
- High-quality dimming of 1…100 % by amplitude dimming
- High quality of light thanks to <1% output ripple current
- Very high efficiency
- Fulfill safety requirement due to overload, overtemperature, Hot Plug protection
- Easy to use in corridors and restrooms because of three-level Corridor function
- Touch DIM application: easy to control via pushbutton or sensor
- Energy efficient Touch DIM operation due to automatic switch-off at sufficient residual light
- Suitable for emergency Installations (acc. to EN 60598-2-22 and IEC 61347-2-13, appendix J) thanks to DC detection (0 Hz, pulsating DC), on/off switchable
- Feedback of power consumption and operating hours (Fit for SMART GRID)
- Suitable for buildings according to EPBD/BREEAM/LEED due to automatic Constant Lumen Output setting
- Luminaire information for easy maintenance
Areas of application
- Linear lighting for office, education, industry, storage areas and retail
- Installation in emergency lighting systems according to IEC 61347-2-13, appendix J
- Suitable for luminaires of protection class I
Technical Data
Electrical data
Nominal input voltage
220…240 V
Mains frequency
0/50/60 Hz
Input voltage AC
198…264 V
Input voltage DC
176…276 V
Current set
DALI / NFC / LEDset / Programmable
Total harmonic distortion
< 10 %
Power factor λ
0.38C...0.96
Efficiency in full-load
93 %
Device power loss
4.0 W
Protective conductor current
<0.5 mA
Inrush current
10 A
Max. ECG no. on circuit breaker 10 A (B)
19
Max. ECG no. on circuit breaker 16 A (B)
30
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
54…240 V
U-OUT (working voltage)
< 250 V
Nominal output current
75…400 mA
Output current LEDset open
35 mA
Output current LEDset shorted
75 mA
Default output current
35 mA
Output current tolerance
±5 %
Output ripple current (100 Hz)
< 1 %
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
4…38 W
Maximum output power
38 W
Galvanic isolation
Non isolated
Power loss in stand-by mode
<0.25 W
Dimensions & weight
Mounting hole spacing, length
350.0 mm
Product weight
180.00 g
Cable cross-section, input side
0.5…0.75 mm²
Cable cross-section, output side
0.5…0.75 mm²
Wire preparation length, input side
8.0…9.0 mm
Wire preparation length, output side
8.0…9.0 mm
Length
360.0 mm
Height
11.0 mm
Width
30.0 mm
Colors & materials
Casing material
Metal
Temperatures & operating conditions
Ambient temperature range
-25…+60 °C
Maximum temperature at tc test point
75 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-25…85 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
50000 / 100000 h
Capabilities
Programming interface
DALI, NFC, LEDset
Dimmable
Yes
Dimming interface
DALI-2 / Touch DIM / Touch DIM Sensor
Dimming range
1…100 %
Dimming method
Full analogue dimming
Constant lumen function
Programmable
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I
Suitable for emergency lighting
Yes
Type of connection, input side
Push terminal
Type of connection, output side
Push terminal
DALI-2 Energy Data
No
Number of channels
1
DALI-2 Diagnostic Data
No
Control interface
DALI
Programming
Programming device
DALI magic / NFC Scanner
Tuner4TRONIC Field App
Yes
Programmable features
Constant Lumen
Yes
DALI-2 Luminaire Data
No
Configuration Lock
Yes
Certificates & standards
Approval marks – approval
CE / EL / VDE-ENEC / VDE-EMC / EAC / CCC / RCM / BIS
Standards
Acc. to EN 61347-1/Acc. to EN 61347-2-13/Acc. to EN 55015/Acc. to EN 61547/Acc. to EN 61000-3-2/Acc. to EN 62384/Acc. to EN 62386
Type of protection
IP20
Logistical data
Commodity code
85044083900
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
24-05-2023
Primary Article Identifier
4052899957022
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
c986deb6-b8d9-457a-8b1b-c23474109f0a
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4052899957022 |
UNV
| 1 | 360mm x 30mm x 11mm | 180.00g | 0.12dm³ |
| 4052899957091 |
VS
| 20 | 385mm x 160mm x 66mm | 3717.00g | 4.07dm³ |
Downloads
Data sheets
Information about Family
Cutting edge design - total design freedom
This driver has a height of only 11mm for cutting edge luminaire design and shows a direct sensor connection with LS PD LI UF TD. The product is fully digitally programmable by DALI and NFC and offers 0.1…100% DALI dimming as well as wide operating windows, up to 550mA.
This driver has a height of only 11mm for cutting edge luminaire design and shows a direct sensor connection with LS PD LI UF TD. The product is fully digitally programmable by DALI and NFC and offers 0.1…100% DALI dimming as well as wide operating windows, up to 550mA.
Product family features
- Line frequency: 0 Hz | 50 Hz | 60 Hz
- Versatile DALI window driver up to 75 W due to flexible output characteristic
- Supply voltage: 220…240 V
- Available with output current range: up to 700 mA
- Direct Ultraflat sensor connection via LEDset (LS/PD LT2 LI UF Sensor)
- Use with Ultraflat DALI sensor (LS/PD DALI LI UF Sensor)
- Constant Lumen Output (CLO)
- Non-isolated drivers
- DALI-2 certified (Part -101,-102 and -207)
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
|
OTi DALI 35/220…240/400 D LT2 UF L
|
54…240 V | 75…400 mA | 360.0 mm | 30.0 mm | 11.0 mm | ||
|
OTi DALI 75/220…240/700 D LT2 UF L
|
54…240 V | 150…700 mA | 360.0 mm | 30.0 mm | 11.0 mm |