PTi 70/220…240 S

Product family benefits
  • Long reliable life at maximum permitted temperatures
  • Compact dimensions and low weight for small luminaire designs
  • Excellent thermal behavior for very high limit temperatures tc and ta
  • Automatic safety shutdown of lamps in the event of a defect or at end of life (EoL)
Areas of application
  • Shop lighting
  • Health and fitness areas (in luminaires with protection class IP66 or higher)
  • Effect and accent lighting

Safety advice
Ballast losses and lamp heat radiation can lead to heat accumulation in a completely closed case. Therefore it is necessary to ensure that the temperature at the measuring point t of the ECG does not exceed the maximum value.
Attention!
For safety reasons disconnect the device before replacing the lamp!
Any conductive material must have a minimum distance of 4 mm to the front of the terminal block.
Installation by qualified electrician only.
Terminals for protective earth not suitable for any through connection.

Technical Data

Electrical data

Lamp wattage

73 W

Maximum output power

73 W

Line current

0.36 A

At 230 VAC

Ignition voltage

4.5 kVp

Operating frequency

0.200…0.240 kHz

System wattage

79.00 W

Efficiency in full-load

92 %

Input voltage AC

198…264 V

Nominal voltage

220…240 V

Mains frequency

50…60 Hz

Power factor λ

0.95

Minimum

Inrush current

45 A

twidth = 250 µs (measured at 50 % Ipeak)

Max. ECG no. on circuit breaker 10 A (B)

7

Type B

Max. ECG no. on circuit breaker 16 A (B)

13

Type B

Max. no. of ECGs on 16A MCB with EBN-OS

32

Type B

Protective conductor current

0.25 mA

U-OUT (working voltage)

250 V

Max. working voltage between LH and LL

250 V

Max. working voltage betw. LL/LH & earth

250 V

Max. capacitance of wire ECG/lamp

120 pF

Dimensions & weight

Length

110.0 mm

Width

75.0 mm

Height

30.0 mm

Mounting hole spacing, length

99.0 mm

Mounting hole spacing, width

64.0 mm

Cable cross-section, input side

0.5…2.5 mm²

Cable cross-section, output side

0.5…2.5 mm²

Wire preparation length, input side

10…11 mm

Wire preparation length, output side

10…11 mm

Product weight

255.00 g

Colors & materials

Casing material

Metal

Temperatures & operating conditions

Ambient temperature range

-25…+55 °C

Maximum temperature at tc test point

85 °C

Lifespan

ECG lifetime

50000 h

At maximum Tc / 10% failure rate

Additional product data

Design / version

Built-in unit

Suitable for lamp power (1 lamp)

73 W

Capabilities

Max. cable length to lamp/LED module

1.5 m

Overheating protection

Power reduction and switch off at T > 85 °C at the tc point

Overvoltage protection at 275…300 V

48 h

Control gear switches off after 40 s

Overvoltage protection at 300…320 V

2 h

Control gear switches off after 40 s

Overvoltage protection at 320…350 V

5 min

Control gear switches off or does not start

ECG reset time

> 0.5 s

Dimmable

No

Restriction on ignition time

20 min

Suitable for fixtures with prot. class

I

Intended for no-load operation

No

Certificates & standards

Approval marks – approval

ENEC 10 / VDE / VDE-EMC / EAC / C-Tick

Type of protection

IP20

EEI – Energy Label

A2

Standards

Acc. to EN 61347-2-12/Acc. to EN 55015/Acc. to EN 61000-3-2/Acc. to EN 61547

Logistical data

Commodity code

85041080900

Environmental information


Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)

Date of Declaration

26-05-2023

Primary Article Identifier

4008321049629

Candidate List Substance 1

Lead

CAS No. of substance 1

7439-92-1

Safe Use Instruction

The identification of the Candidate List substance is sufficient to allow safe use of the article.

Declaration No. in SCIP database

0b818340-d638-4445-9933-2ebbeaa7f5be

Packaging information

EAN

Unit

Piece

Dimension l x w x h

Weight

Volume

4008321049629 UNV

Unpacked

1 110mm x 75mm x 30mm 255.00g 0.25dm³
4008321049636 VS

Shipping box

20 412mm x 152mm x 136mm 5370.00g 8.52dm³

Downloads

Information about Family

POWERTRONIC INTELLIGENT PTi S is an electronic control gear (ECG) for use with high intensity discharge lamps that you install within the luminaire. It has an energy efficiency index of A2 and is particularly suitable for use in shoplighting, health and fitness settings (when installed in dry, corrosion-resistant areas) and for the creation of effect and accent lighting. POWERTRONIC INTELLIGENT PTi S is long-lived and reliable at maximum temperatures, and its compact dimensions and low weight make it easy to install even in small luminaires. It exhibits excellent thermal behavior for very high limit temperatures tc and ta, and gives you the reassurance of automatic lamp shutdown in the event of malfunction or the end of life.
Product family features
  • Energy Efficiency Index EEI: A2
  • Supply voltage: 220…240 V
  • Line frequency: 50…60 Hz
  • RI suppression: to EN 55015/CISPR 15
  • Safety: to EN 61347-2-12
  • Line harmonics according to EN 61000-3-2
  • Immunity according to EN 61547
Ecodesign regulation information:
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.

Products

Sort by:
Product
Height
Length
Nominal voltage
Lamp wattage
Ignition voltage
Data sheet
PTi 35/220…240 S
30.0 mm 110.0 mm 220…240 V 39 W 4.5 kVp
PTi 35/220…240 S MINI
30.0 mm 97.0 mm 220…240 V 39 W 3.0 kVp
PTi 70/220…240 S
30.0 mm 110.0 mm 220…240 V 73 W 4.5 kVp
PTi 150/220…240 S
31.0 mm 150.0 mm 220…240 V 147 W 4.5 kVp