PTo 150/220…240 3DIM

Product family benefits
  • Energy savings up to 30 % (compared to CCG operation) thanks to 3DIM (except PTo 35)
  • High surge protection: up to 3 kV (L-N) / 4 kV (L/N-PE)
  • Automatic safety shutdown of lamps in the event of a defect or at end of life (EoL)
  • Excellent thermal behavior for very high limit temperatures tc and ta
Areas of application
  • Suitable for luminaires of protection classes I and II
  • Suitable for outdoor applications in luminaires with IP > 54

Safety advice
Ballast losses and lamp heat radiation can lead to heat accumulation in a completely closed case. Therefore it is necessary to ensure that the temperature at the measuring point t of the ECG does not exceed the maximum value.
For safety reasons disconnect the device before replacing the lamp!

Technical Data

Electrical data

Lamp wattage

147 W

Maximum output power

147 W

Line current

0.71 A

At 230 VAC

Ignition voltage

4.5 kVp

Operating frequency

0.165 kHz

System wattage

16000 W

Efficiency in full-load

91 %

Input voltage AC

198…264 V

Nominal voltage

220…240 V

Nominal input voltage (SD port)

220…240 V

In relation to L/N

Mains frequency

50…60 Hz

Power factor λ



Inrush current

70 A

twidth = 250 µs (measured at 50 % Ipeak)

Max. ECG no. on circuit breaker 10 A (B)


Type B

Max. ECG no. on circuit breaker 16 A (B)


Type B

Max. no. of ECGs on 16A MCB with EBN-OS


Type B

Protective conductor current

0.1 mA

U-OUT (working voltage)

250 V

Max. working voltage between LH and LL

250 V

Max. working voltage betw. LL/LH & earth

250 V

Max. capacitance of wire ECG/lamp

120 pF

Surge capability (L-N)

3 kV

Surge capability (L/N-Ground)

4 kV

Dimensions & weight


1580 mm


940 mm


425 mm

Mounting hole spacing, length

148.0 mm

Cable cross-section, input side

0.5…2.5 mm²

Cable cross-section, output side

0.5…2.5 mm²

Wire preparation length, input side

10…11 mm

Wire preparation length, output side

10…11 mm

Product weight

90000 g

Colors & materials

Casing material


Temperatures & operating conditions

Ambient temperature range

-25…+55 °C

Maximum temperature at tc test point

85 °C


ECG lifetime

60000 h

At Tcase = 80°C at Tc point / 10% failure rate

ECG ambient temperature (ta)

50 °C

55 °C

Temperature at the measuring point tc (°C)

80 °C

85 °C

ECG lifespan (h)

60000 h

40000 h

Additional product data

Required IP rating of luminaire

> 54

Design / version

ECG outdoor

Suitable for lamp power (1 lamp)

147 W


Dimming interface

DALI / StepDIM / AstroDIM

Dimming range

60…100 %

Max. cable length to lamp/LED module

1.5 m

Burn-in time prior to dimming operation

10 min

Overheating protection

Power reduction and switch off at T > 85 °C at the tc point

ECG reset time

> 0.5 s



Restriction on ignition time

20 min

Suitable for fixtures with prot. class

I / II

Lightning stroke protection

With connected equipotentiality-terminal 10 surges with 10 kV acc. to IEC 61000-4-5

Intended for no-load operation


Certificates & standards

Approval marks – approval

ENEC 10 / VDE / VDE-EMC / EAC / C-Tick

Type of protection


EEI – Energy Label



Acc. to EN 61347-2-12/Acc. to EN 55015/Acc. to EN 61000-3-2/Acc. to EN 61547/Acc. to EN 62386-101/Acc. to EN 62386-102/Acc. to EN 62386-103

Logistical data

Commodity code


Environmental information

Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)

Date of Declaration


Primary Article Identifier


Candidate List Substance 1


CAS No. of substance 1


Safe Use Instruction

The identification of the Candidate List substance is sufficient to allow safe use of the article.

Declaration No. in SCIP database


Packaging information




Dimension l x w x h



4008321956385 UNV


1 1045.00g
4008321956392 VS

Shipping box

10 313mm x 273mm x 193mm 10450.00g 16.49dm³


Information about Family

POWERTRONIC OUTDOOR PTo is an electronic control gear (ECG) for use outside in professional lighting installations with high intensity discharge lamps. It gives you 3DIM functionality (StepDIM/AstroDIM/DALI), lightning protection up to 10 kV, an energy efficiency index of A2 and luminous flux factor 1 compared with CCG operation. You can use it outside in luminaires with protection of IP54 or greater, and in luminaires of protection classes I and II. Its many benefits include excellent thermal behavior at very high limit temperatures tc and ta; high surge protection (up to 3 kV (L-N) / 4 kV (L/N-PE); energy savings of up to 30 % compared to CCG operation due to 3DIM functionality (except PTo 35) and the assurance of automatic lamp shutdown in the event of defect or end of life.
Product family features
  • 3DIM functionality (StepDIM/AstroDIM/DALI)
  • Energy Efficiency Index EEI: A2
  • Lightning protection: up to 10 kV
  • Supply voltage: 220…240 V
  • Line frequency: 50…60 Hz
  • Line harmonics according to EN 61000-3-2
  • Immunity according to EN 61547
  • RI suppression: to EN 55015
  • Safety: to EN 61347-2-12
  • Luminous flux factor 1 compared with CCG operation
  • Not suitable for DC operation
Ecodesign regulation information:
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.


Sort by:
Nominal voltage
Lamp wattage
Ignition voltage
Data sheet
PTo 50/220…240 3DIM
480 mm 220…240 V 1330 mm 50 W 4.5 kVp
PTo 100/220…240 3DIM
42.5 mm 220…240 V 158.0 mm 97 W 4.5 kVp
PTo 150/220…240 3DIM
425 mm 220…240 V 1580 mm 147 W 4.5 kVp