PTi 150/220…240 I

Product family benefits
  • Extended terminal section enables mains looping
  • Screw-down cable clamps for reliable strain relief
  • Long reliable life at maximum permitted temperatures
  • Automatic safety shutdown of lamps in the event of a defect or at end of life (EoL)
Areas of application
  • Shop lighting
  • Health and fitness areas (in luminaires with protection class IP66 or higher)
  • Effect and accent lighting

Safety advice
Ballast losses and lamp heat radiation can lead to heat accumulation in a completely closed case. Therefore it is necessary to ensure that the temperature at the measuring point t of the ECG does not exceed the maximum value.
Attention!
For safety reasons disconnect the device before replacing the lamp!

Technical Data

Electrical data

Lamp wattage

147 W

Maximum output power

147 W

Line current

0.72 A

At 230 VAC

Ignition voltage

4.5 kVp

Operating frequency

0.165 kHz

System wattage

160.00 W

Efficiency in full-load

92 %

Input voltage AC

198…254 V

Nominal voltage

220…240 V

Mains frequency

50…60 Hz

Power factor λ

0.95

Minimum

Inrush current

70 A

twidth = 250 µs (measured at 50 % Ipeak)

Max. ECG no. on circuit breaker 10 A (B)

4

Type B

Max. ECG no. on circuit breaker 16 A (B)

7

Type B

Max. no. of ECGs on 16A MCB with EBN-OS

17

Type B

Protective conductor current

0.4 mA

U-OUT (working voltage)

250 V

Max. working voltage between LH and LL

250 V

Max. working voltage betw. LL/LH & earth

250 V

Max. capacitance of wire ECG/lamp

120 pF

Dimensions & weight

Length

212.0 mm

Width

93.0 mm

Height

33.0 mm

Mounting hole spacing, length

203.0 mm

Cable cross-section, input side

0.75…2.5 mm²

Cable cross-section, output side

0.75…2.5 mm²

Wire preparation length, input side

10…11 mm

Wire preparation length, output side

10…11 mm

Product weight

420.00 g

Colors & materials

Casing material

Plastic

Temperatures & operating conditions

Ambient temperature range

-25…+50 °C

Maximum temperature at tc test point

75 °C

Lifespan

ECG lifetime

40000 h

At maximum Tc / 10% failure rate

Additional product data

Design / version

With cable clamp

Suitable for lamp power (1 lamp)

150 W

Capabilities

Max. cable length to lamp/LED module

1.5 m

Overheating protection

Power reduction and switch off at T > 75 °C at the tc point

ECG reset time

> 0.5 s

Cable/wire types, input side

NYM-J 3x1.5 / NYM-J 3x2.5 / H05VV-F 3x1.5 / NHXMH-J 3x1.5 mm²

Cable/wire types, output side

SIHF-J 3x1.5 / SIHF-J 3x2.5 / SIHSI 3x1.0 mm²

Dimmable

No

Restriction on ignition time

20 min

Suitable for fixtures with prot. class

I

Intended for no-load operation

No

Certificates & standards

Approval marks – approval

ENEC 10 / VDE / VDE-EMC / EAC / C-Tick

Type of protection

IP20

EEI – Energy Label

A2

Standards

Acc. to EN 61347-2-12/Acc. to EN 55015/Acc. to EN 61000-3-2/Acc. to EN 61547/Acc. to EN 61347-2-12/Acc. to EN 62493

Logistical data

Commodity code

85041080900

Environmental information


Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)

Date of Declaration

26-05-2023

Primary Article Identifier

4008321915535

Candidate List Substance 1

Lead

CAS No. of substance 1

7439-92-1

Safe Use Instruction

The identification of the Candidate List substance is sufficient to allow safe use of the article.

Declaration No. in SCIP database

8ab6db02-47b2-4112-8211-db4ec755751b

Packaging information

EAN

Unit

Piece

Dimension l x w x h

Weight

Volume

4008321915535 UNV

Unpacked

1
4008321915542 VS

Shipping box

20 488mm x 453mm x 100mm 9440.00g 22.11dm³

Downloads

Information about Family

POWERTRONIC INTELLIGENT PTi I is an electronic control gear (ECG) for use with high intensity discharge lamps, that has an energy efficiency index (EEI) of A2. It is supplied with screw-down cable clamps for reliable strain relief, and you may find it particularly good for use in shoplighting, health and fitness spaces (in dry, corrosion-protected areas) and for effect and accent lighting. It has an extended terminal section that enables mains looping, and a long lifespan at maximum permitted temperatures. POWERTRONIC INTELLIGENT PTi I gives you reliable service and provides automatic lamp shutdown in the event of a defect or end of life.
Product family features
  • Energy Efficiency Index EEI: A2
  • Supply voltage: 220…240 V
  • Line frequency: 50…60 Hz
  • RI suppression: to EN 55015/CISPR 15
  • Safety: to EN 61347-2-12
  • Line harmonics according to EN 61000-3-2
  • Immunity according to EN 61547
Ecodesign regulation information:
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.

Products

Sort by:
Product
Height
Length
Nominal voltage
Lamp wattage
Ignition voltage
Data sheet
PTi 35/220…240 I
32.0 mm 171.0 mm 220…240 V 39 W 4.5 kVp
PTi 70/220…240 I
32.0 mm 171.0 mm 220…240 V 73 W 4.5 kVp
PTi 150/220…240 I
33.0 mm 212.0 mm 220…240 V 147 W 4.5 kVp