OT FIT 500/220...400/1A6 D NFC HC B L
Product family benefits
- Flexible and future-proof current setting via NFC (Near Field Communication)
- Lifetime: up to 100,000 h (temperature at Tc = 65 °C, max. 10 % failure rate)
- Higher quality of light thanks to < 1% output ripple current
- Very high efficiency (up to 97%)
- Protection against 4 kV burst and 2 kV surge voltage (L-N and L-N/PE)
Areas of application
- Linear and area lighting
- Horticulture lighting
- Industry lighting
- Suitable for luminaires of protection class I
Technical Data
Electrical data
Nominal input voltage
220…400 V
Mains frequency
50…60 Hz
Input voltage AC
198…440 V
Current set
NFC
Power factor λ
> 0.98
Efficiency in full-load
96 %
Device power loss
24 / 19 W
Inrush current
9.4 / 15.9 A
Max. ECG no. on circuit breaker 10 A (B)
-
Max. ECG no. on circuit breaker 10 A (C)
-
Max. ECG no. on circuit breaker 16 A (B)
5 / 12
Max. ECG no. on circuit breaker 16 A (C)
5 / 15
Max. ECG no. on circuit breaker 25 A (B)
8 / 18
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
2 kV
Nominal output voltage
150…550 V
Nominal output current
400…1600 mA
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
200…525 W
Maximum output power
525 W
Galvanic isolation
Non isolated
Default output current
400 mA
Output ripple current (100 Hz)
< 1 %
Dimensions & weight
Mounting hole spacing, length
258.0 mm
Product weight
1400.00 g
Height
43.0 mm
Length
312.0 mm
Width
136.0 mm
Temperatures & operating conditions
Ambient temperature range
-25…+50 °C
Maximum temperature at tc test point
50 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-40…+85 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
100000 / 50000 h
Additional product data
Encapsulated
No
Capabilities
Dimmable
No
Overheating protection
Yes
Overload protection
Yes
Short-circuit protection
Yes
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.5 m
Suitable for fixtures with prot. class
I
Number of channels
1
Control interface
NFC
Programming
Programming device
DALI magic / FEIG
Tuner4TRONIC Field App
Yes
Tuner4TRONIC
Yes
Certificates & standards
Approval marks – approval
CE
Standards
Acc. to EN 61347-1/Acc. to EN 61347-2-13/Acc. to EN 62384/Acc. to EN 61000-3-2/Acc. to EN 61000-3-3/Acc. to EN 61547
Type of protection
IP20
Logistical data
Commodity code
85044083900
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
30-06-2023
Primary Article Identifier
4052899624436
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
ded81c24-8505-42b9-8430-f8e83477fc0d
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4052899624436 |
UNV
| 1 | 312mm x 136mm x 43mm | 1400.00g | 1.82dm³ |
| 4052899624450 |
VS
| 5 | 345mm x 265mm x 165mm | 7468.00g | 15.09dm³ |
Downloads
Data sheets
Information about Family
Product family features
- 1- and 2-channels drivers
- Line frequency: 47.5…60 Hz
- Versatile scope of application due to output power range of up to 1050 W
- Supply voltage: 220…240 V / 400 V
- Available with output current range: up to 1,600 mA
- Non-isolated drivers
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
|
OT FIT 500/220...400/1A6 D NFC HC B L
|
150…550 V | 400…1600 mA | 312.0 mm | 136.0 mm | 43.0 mm | ||
|
OT FIT 1000/220...400/1A6 D NFC HC 2CH B L
|
150…550 V | 400…1600 mA | 312.0 mm | 136.0 mm | 43.0 mm |