OT FIT 40/220 240/350 D CS L
Product family benefits
- Flexible current setting (DIPswitch 6 currents)
- Higher quality of light thanks to low output ripple current
- High efficiency
- User flexibility with six different output currents from one driver
- Safety requirement due to overload, overtemperature, short-circuit protection
- Long reliable life at maximum permitted temperatures
- Enable slim fixture design with flat 21 mm height metal housing
Areas of application
- Linear and area lighting
- Office, industrial and shop lighting
- Suitable for luminaires of protection class I
- Installation in emergency lighting systems according to IEC 61347-2-13, appendix J
- Suitable for installation in emergency lighting systems according to EN 60598-2-22
Technical Data
Electrical data
Nominal input voltage
220 240 V
Mains frequency
0/50/60 Hz
Input voltage AC
198 264 V
Current set
DipSwitch
Power factor λ
082C 099
Efficiency in full-load
91 %
Device power loss
4.15 W
Inrush current
14.8 A
Max. ECG no. on circuit breaker 10 A (B)
19
Max. ECG no. on circuit breaker 16 A (B)
30
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
40 120 V
Nominal output current
100 / 150 / 200 / 250 / 300 / 350 mA
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
8...42 W
Maximum output power
42 W
Output ripple current (100 Hz)
< 3 %
Dimensions & weight
Mounting hole spacing, length
200.0 mm
Product weight
11600 g
Cable cross-section, input side
0.5 1.5 mm²
Wire preparation length, input side
8.0 9.0 mm
Width
300 mm
Height
210 mm
Length
2100 mm
Temperatures & operating conditions
Ambient temperature range
-25 +50 °C
Maximum temperature at tc test point
75 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-25 85 °C
Permitted rel. humidity during operation
5 85 %
Lifespan
ECG lifetime
50000 / 100000 h
Capabilities
Dimmable
No
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I
Number of channels
1
Programming
Programming device
DIPswitch
Certificates & standards
Approval marks approval
CE / ENEC / CCC / RCM / UKCA / BIS / EAC
Standards
Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 61547/Acc. to EN 55015
Type of protection
IP20
Logistical data
Commodity code
85044083900
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
26-09-2023
Primary Article Identifier
4062172285278
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
47470c35-a656-42ce-8ae3-d368b425c9ae
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
---|---|---|---|---|---|
4062172285278 |
UNV
| 1 | 210mm x 30mm x 21mm | 116.00g | 0.13dm³ |
4062172285285 |
VS
| 20 | 237mm x 162mm x 130mm | 2629.00g | 4.99dm³ |
Downloads
Information about Family
Product family features
- Line frequency: 0 Hz | 50 Hz | 60 Hz
- Supply voltage: 220 240 V
- Line voltage: 198 264 V
- DC detection (0 Hz, pulsating DC), on/off switchable
- Wide output current range
- Lifetime: up to 100,000 h (temperature at Tc = 65 °C, max. 10 % failure rate)
- Non-isolated drivers
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
Product |
|
|
|
|
|
Data sheet | ||
---|---|---|---|---|---|---|---|---|
OT FIT 18/220
240/350 D CS L
|
32...54 V | 100 / 150 / 200 / 250 / 300 / 350 mA | 2100 mm | 300 mm | 210 mm | |||
OT FIT 40/220
240/350 D CS L
|
40 120 V | 100 / 150 / 200 / 250 / 300 / 350 mA | 2100 mm | 300 mm | 210 mm | |||
OT FIT 60/220
240/350 D CS L
|
90 175 V | 100 / 150 / 200 / 250 / 300 / 350 mA | 210.0 mm | 30.0 mm | 21.0 mm | |||
OT FIT 75/220...240/550 D CS L
|
90 216 / 90 188 / 90 167 / 90 150 / 90 136 V | 300 / 350 / 400 / 450 / 500 / 550 mA | 2100 mm | 300 mm | 210 mm |